How To Clean Dyson V6

How To Clean Dyson V6 – Do You Know How?

Does your Dyson vacuum cleaner give out a dirty, dusty smell every time you use it? Is the suction not as good as it once was?

The first thing most people do is rush out to the store to spend more money on a vacuum.

Let’s stop you right there as sometimes your vacuum just needs a really good, deep cleanout, which can then have it working like new again.

When was the last time you cleaned out your vacuum?

Did you know you can actually extend the life of your vacuum just by giving it a good clean-out every so often?

Not just the bag or the canister but the whole vacuum? Never? Well, we are here to explain how to deep clean your Dyson v6.

How To Clean Dyson V6?

Cleaning your Dyson V6 entails a little bit of work, but it will give you a more efficient clean, and the vacuum will last longer. You need to completely unplug the Dyson, then empty and scrub the canisters out, take out the filters and wash them, then you can air dry them while you untangle any mess in the head bar. Now check the hose for clogs and clean over the exterior of the Dyson. Now put it all back together, and you’re ready to go about your cleaning business.

What Is a Dyson Vacuum Cleaner

The Dyson vacuum cleaners use what is called cyclonic separation tech that helps to get rid of particles, dirt, and dust.

The technology the Dyson brand has enables the air that is sitting inside to spin around fast. This allows for consistent and strong suction.

The vacuum uses a three-step cleaning process that gathers the dust and dirt through a filter. It then goes to the bin that catches the big particles, which are separated.

This lowers the risk of your vacuum clogging up, which will allow for constant, long-lasting suction.

Always empty the canister after each vacuum, so the debris and dirt don’t build up too much.

Dyson is known as a long-lasting, brand, easy to use, and due to popular demand, the vacuums can be found in most households.

Now just how do we clean the system? It’s simple, really.

First, Unplug The System

Before you start removing any parts to clean the vacuum, you want to ensure it is turned off at the PowerPoint and unplugged.

This will make the job easier and safer, eliminating your risk of getting shocked.

Cleaning Out The Canisters

Now you want to start with the canister; you will always deal with canisters as with Dyson’s they are all bagless machines.

In most machines, the dust canister can be found underneath the cyclone area. You will see a red button that says bin release located near the base.

You can press this, and it will push out the flap so you can release the canister from the vacuum itself. If you cannot find it check your owner’s manual.

Once you have pressed the button on the canister, it will release the base, so the dust and dirt can fall straight into the bin.

Give it a good shake to get out as much dust as you can. Now you need a clean microfiber cloth to clean out the inside of the canister.

Microfiber material is a good option as it happens to already be positively charged. This allows it to easily attract and catch the dust particles so they won’t get smeared back into the canister afterward.

Dyson says not to use any types of harsh detergents to wash out the dust canister as chemicals can react and damage the plastic or make the material sticky.

If you have particles that are stuck, you can try using a cloth dipped in plain water with a little vinegar added to help loosen the grime.

Sometimes an air compressor works well, which allows you to blast out any debris to give you maximum suction.

If you use a damp cloth, ensure the canister is dried well, as any lingering moisture or dampness can lead to the growth of mold.

Removing The Filters And Washing Them

The Dyson filter plays a very important part in cleaning your home. It works hard to trap dirt particles, bacteria, and even pollen from the floor and air.

This means that it is vital to clean out the filters often. You can lift the filter out and remove it so it can be cleaned, the filters are often colored purple, so they are easily spotted.

You will need to double-check the model of Dyson you have, as some will have more than one filter.

The filter can be placed under running cold water, which will be enough to remove the dust and particles.

If the filter is extra dirty, give it a good shake out first to try and remove most of the dust. Again you don’t want to be using any harsh chemicals which can damage the filter pads.

Now give the filter a good squeeze out, and if the water coming out is still dirty, repeat the process until the water coming out is clean.

Now before the filter is able to go back inside the vacuum, it needs to be completely dried through.

You can only air dry the filters as putting them in the dryer will damage them and pull them out of shape.

Avoid direct sunlight also and allow the time it may take to dry, which can be up to 24 hrs depending on the weather or temperature of the room.

If you use your vacuum often and have heavily soiled floors, it is best to wash them frequently to keep them in good condition.

You can buy new vacuum filters, and it is a good idea to do so after a few times of washing them.

The filters can be rinsed a few times but overdoing it can stop the filters from working as they should, and they may not catch the dust and dirt as they ought to, which means it will go elsewhere and ruin the vacuum cleaner.

Now To Untangle The Brush Bar

This part can get a little complicated as you will need to remove the soleplate to gain full access to the brush bar.

You might need a flathead screwdriver to turn the screw slightly to allow the plate to open.

The brush bar collects the debris, dirt, and hair from your carpet and floors. This will build up over time, and the things that are picked up get tangled around it like pieces of cotton and long hair.

This will greatly reduce the cleaning power as the brush cannot spin at the right speed to pick up the particles.

You might need a sharp knife or pair of scissors to cut away the bulk first, especially if you haven’t cleaned this before.

You could certainly be dealing with a fair lot of bulk. Be careful when using the scissors that you don’t cut any of the bristles that belong to the vacuum, as this will make the vacuum more efficient.

The compartment area where the brush bar is located can get really dusty. If this is the case, you can use a damp microfiber cloth to clean it, as long as you make sure it is completely dry before you go ahead and put it back together again.

A clever little trick is to use a quick unpick that you can get from your local craft store. They work very well to get through the hair and cotton etc.

Time To Unclog The Hose

After a while, the hose can become blocked and clogged with debris and hair, which can affect how much suction power you are getting.

Disconnect the hose from your Dyson, which can be done via a little red button that is located on the wand.

You need to visually check the hose to see if there is any debris or build-up that is blocking the tube.

If you can see some, use a broom or mop handle to brush it through. Don’t vacuum this back up as it will cause another blockage just dispose of it in the bin.

The hose is only thin material which is why you want to avoid using any type of harsh chemicals as it can cause irreversible damage.

However, you can use a vinegar cleaning solution which will help to kill bacteria and germs sitting inside the pipes.

You can fill up your sink or basin with clean, warm water, then go ahead and add one full cup of white distilled vinegar.

Swirl it around and then submerge the hose into the mixture. You can let the hose sit for a few minutes then you can use your tap to flush the mixture and debris out.

You can do this outside and use your hose if your sink is not big enough.

It can also be done by holding your Dyson hose in a U shape.  Make sure the hose is completely dry before you go ahead and reconnect your vacuum.

It is good to let the hose dry overnight to ensure it is fully dry. Don’t dry in the sun as the sun’s warmth and the plastic together will create moisture that will remain in the hose.

Cleaning The Exterior

Now that you have fully cleaned out the inside of your vacuum, you can’t stop there. You need to clean the outside of your Dyson to; a damp microfiber cloth works well for this job.

They squeeze out well, so they won’t get oversaturated. To give an overall good clean, sanitize the soleplate and wheels of the vacuum.

Your wheels are rolling around on the floors each time you vacuum and are already dirty, then you vacuum again, tracking that dirty back onto your floors.

You can use diluted vinegar as it works well to disinfectant surfaces, and it won’t harm the soleplate or the wheels.

Now You Can Start To Vacuum

Cleaning your Dyson is an important task that you need to complete often to keep it in working condition and doing its job properly.

Your Dyson will last you longer if you look after it. Make sure that your Dyson is always unplugged and fully dried before plugging it back in just to be safe.

Always start with the dust canister, then dust out the filters, then go ahead and clean your filter. You will be surprised how well the vacuum cleans your floors once it has had a good clean itself.

Giving your vacuum a good clean can give it a new lease on life. It doesn’t take much, and it can save you from having to buy a new vacuum as the Dyson brand vacuums don’t come cheap.

It is a good idea to keep your floor cleaned frequently as the more build-up your vacuum is picking up, the more it might end up clogged and struggle with the heavy loads.

Frequently Asked Questions About How To Clean Dyson V6

How Often Should I Deep Clean My Dyson?

It is a good idea to deep clean your Dyson every few months. You need to empty the canister after each use. This will ensure that your carpet is being cleaned each time properly.

Should I Replace My Filter Pads for my Dyson?

Filter pads for a Dyson vacuum cleaner can be cleaned a few times, but after that, it is best to buy a replacement as washing too much will start to disintegrate the fibers and make them less effective.


Leave a Comment

Your email address will not be published. Required fields are marked *